4 pieces of EVA foam with single sided self-adhesive
Customizable - cut to size as required
Ideal for installing 7mm or 7.5mm HDDs into standard 2.5” hard drive enclosures designed for 9.5mm high HDD
These Self-adhesive Foam Pads fill the space between a drive and the drive enclosure, cutting down on the possible range of movement of a drive and therefore reducing the risk of damage to the drives SATA connection.
SSD/HDDs vary in depth - either 7 or 7.5mm - leaving a relatively large amount of space for them to move in a 2.5" drive enclosure or housing.
Overtime, everyday knocks or movement can fatigue an unsecured drive's connection to the rest of the PC, causing the connection to fail and - in a worse case scenario - damage the SATA connection pins making the drive virtually inoperable.
By filling the gap between the drive and the housing with a foam pad you can cushion the drive and help reduce the risk of damage to it or its connections.
Additional benefits of installing these pads include some reduction in vibration transmissions from HDDs, helping cut down on general running noise. Dimensions (each piece) 10x9.5x2.5mm (WxDxH).
Converter for 2.5" hard drives and SSDs with 22/29-pole SATA Backplane connection
Fits into every standard 3,5" slot with screw fixing on the underside
Also fits into any 3.5" SATA Backplane - has identical dimensions and connections as a 3.5" SATA HDD
Supports SATA hard drives and SSDs with installation heights of up to 15mm
Converter with latching lever and automatic ejection mechanism
Simply install this adapter frame and converter into the 3.5" slot on your desktop or you can use it like a 3.5" drive in a 3.5" converter!
2.5" drives only need a fraction of the energy needed by a 3.5" drive and a voltage supply of just 5V instead of 5V and 12V. They generate considerably less heat and are considerably quieter when running.
As this adapter frame has the same dimensions and SATA connections as a 3.5" SATA hard drive, it can be used just like a 3,5" SATA drive - this solution uses considerably less energy and produces less heat and noise.
Many PC enclosures allow you to attach 3.5" format hard drives and converters on the underside. This is also possible for this converter.
With converter housings where only side screw attachment is possible, this converter does not have the screw attachment at the same positions as a 3.5" drive: the 3 threaded holes on the side have a clearance from the bottom of 6mm instead of 5mm, only the hole at the extreme rear has the same clearance from the front edge (115 mm); the two front holes however have a clearance of 25 and 85 mm from the front edge.
If 1mm of space is available above the slot, this allows the converter to usually only be attached with the threaded holes at the rear.
Where this is not possible, you can use the LINDY converter No.20969 (max. drive height of 7.5 mm) with standard side attachment instead
Allows you to add extra storage to your machine (SSD is not included)
Designed for use with mSATA or SATA based M.2 SSDs
SATA ODD Slim SATA 13 Pin connector to mSATA and M.2*
Dimensions: 128 x 129 x 12.7mm (WxDxH); fits most standard optical drive bays
The LINDY Slim ODD Caddy for mSATA and M.2 SSD allows you to install M.2 and mSATA SSDs* in your notebook using the optical drive bay. This in turn can be used to add extra storage or dual boot capabilities to your computer.
Fully integrates into your laptop or notebook, no cables, external power supplies or software drivers required.
*If both M.2 and mSATA SSDs are installed at the same time, only M.2 will work.
Note: This caddy does not support 3.3V HDDs/SSDs and has been designed to fit most 'standard' and 'universal' CD/DVD/Optical drive bays. Due to variations in laptop design, compatibility with all machines cannot be guaranteed.
Add four 2.5" hard drives or SSDs (not included) to a 5.25" bay
Suitable for hard drives up to 15mm (0.59in) max. height
RAID compatible when connected to a suitable RAID controller
Plug & Play, hot swappable, lockable
2 year warranty
The Lindy SAS/SATA RAID Backplane System is an internal drive housing that supports up to four 2.5" SAS/SATA hard drives in a single 5.25" expansion bay. It can easily be installed into a case or expansion system and is ideal for servers and workstations alike, allowing instant hot-swap access to the hard drives. To add RAID functionality, the backplane system can simply be added to a computers RAID controller.
Two integrated ventilation fans ensure high performance drive cooling. To protect data, each tray features a mechanical lock.
Allows you to add extra hard drive storage (hard drive is not included)
Designed for use with 2.5" SATA hard drives up to 9.5 mm high
SATA ODD Slim SATA 13 Pin Way connector to SATA HDD 22 Way connector
SATA III / 6Gbps
Fully integrates into your laptop or notebook, no cables, external power supplies or software drivers required
Stainless steel & black plastic finish
Dimensions: 128 x 129 x 9.5mm (WxDxH); fits most standard optical drive bays
Note: This caddy does not support 3.3V HDDs/SSDs and is designed to fit most 'standard' and 'universal' CD/DVD/Optical drive bays. Due to variations in laptop design, compatibility with all machines cannot be guaranteed.
Allows the installation of up to two 2.5” HDD’s or SSD’s in a single 3.5” drive bay.
Easily expand or upgrade the mass storage of a PC, server or workstation
Built to ensure maximum compatibility with 2.5” drives
Suitable for drives up to 9.5mm in height
2 year warranty
The Lindy 2 x 2.5" HDD Expansion Bracket is a compact, intuitive solution for the installation two 2.5" hard drives or solid-state drives (SSD) into a single 3.5" drive bay. Ideal for use with small form factor PC's, workstations and servers.
The design ensures compatible PC's can be optimised with single, or dual SSD's, providing exceptional read and write speeds, as well as un-paralleled security and reliability over traditional disk-based drives.