Extends DVI-D video signals up to 50m using low cost CAT5e/5 Cable (not included)
Supports resolutions from 800x600 up to 1920x1200 including 1080p
Power consumption: 1.6W (5V 320mA)
HDCP not suported
2 year warranty
Please note: picture is for illustration purposes only. Network cable is not included.
With this Extender you can use up to 70m of high quality inexpensive Cat.5e/6 cable to connect a DVI source to a DVI display device.
The slim RJ45 connectors and Cat.6 cable (not included) allow greater flexibility not possible with larger DVI connectors and cables.
Normal operation will not require external power; however the Transmitter unit allows external power to be attached in cases where the graphics card does not provide sufficient power, either using a USB Micro-B Cable or an external power supply (5V 320mA) connected to the supplied USB to DC cable.
The Extender supports the following resolutions/distance combinations
800x600 up to 70m
1024x768 up to 65m
1280x1024 to 1920x1200 up to 50m
RJ-45 patch cable: 1 x CAT5e/6 UTP Cable
Transmitter and Receiver Units
USB Micro-B Male to DC (5.5/2.5mm Outer/Inner) Female Adapter Cable, Overall length 12cm
For use with high-resolution monitors up to 2560x1600
Supports DVI-D Dual Link resolutions up to 2560 x 1600
For Single Link resolutions up to 1920 x 1200 or 1080p, please use our DVI Single Link Extender No. 32669
With almost all graphics cards and when using LINDY Super Long Distance cables (SLD), supports cable lengths up to 10m at input + 10m at output
Depending on the quality of the graphics chipset and the stability of the output signal, cable lengths up to 25 m are also supported on both input and output. The following section has some examples. These results may vary as a result of series dispersion or with different graphic card manufacturers.
Extend DVI-D Dual Link signals up to 500m using a single fibre optic cable (not included)
Compatible with DVI-D 2.0 specifications including HDTV & HD-Ready displays
Supports HDTV resolutions up to 2560 x 1600 @ 60Hz / 1600p @ 60 Hz
Auto & Self learning EDID transmission
No HDCP support
Auto laser cut off if fibre optic cable is broken or DVI-D cable removed
2 year warranty
Easy to set up and install this compact Fibre Optic DVI-D Dual Link Extender is a cost effective, high quality solution for sending DVI-D signals up to 500m without any compression or degradation over MPO Multimode cable.
Unlike other solutions, this extender uses just a single fibre cable to reach such great lengths. The system comprises of transmitter and receiver modules that connect directly to the digital source & display via DVI-D. The modules are then connected using a single, MPO fibre optic cable (not included).
Please note - We recommend using 50/125µ or 62.5/125µ MPO multimode fibre cable. Please contact Technical Support for further advice.
This DVI-D/SDI converter is a favourable alternative for outputting DVI-D signals in the SDI format. It supports 1080p resolutions and allows you to select between the 3.5mm analogue stereo input and digital input in the audio contained in the DVI signal.
Extends DVI-D signals at distances of up to 500m using dual fibre optic cables (not included)
Compatible with DVI-D 2.0 specifications including HDTV and HD-Ready displays
Supports HDTV resolutions up to 1920 x 1200 @ 60Hz / 1080p @ 60 Hz
6Gbps Total Bandwidth over Dual Duplex or 4x LC Simplex Fibre Optic Cables
2 year warranty
Easy to set up and install the compact LINDY LC Fibre Optic DVI-D Extender is the most cost effective, high quality solution on the market for sending DVI-D signals over incredible distances. Send DVI-D signals without compression or any degradation over standard LC duplex multimode (50/125µm) fibre cable up to 500m (not included).
The extender system comprises two modules, a transmitter and a receiver, which are connected directly to both the DVI-D source and display. The modules are then connected together using two, standard 'off the shelf' LC Duplex Fibre cable fibre optic cables (not included).
1 x Transmitter Unit
1 x Receiver Unit
1 x Multi-country PSU for Receiver, 5VDC, =1A, with Adapters for US/EUR/UK/AUS